Maintenance method:
1. The biochemical incubator should be installed as close as possible to the place where the air is quiet and the temperature changes little. Use a three-prong plug and the socket should be properly grounded.
2. Before opening the biochemical incubator, you should be familiar with and understand the instructions of each component instrument and instrument, and master the correct method of use.
3. It is strictly forbidden to contain volatile chemical solvents, explosive gases and flammable gases are placed in the box; flammable sprays should not be used near the incubator to avoid spark ignition.
4. Always pay attention to the gas path.
5. The biochemical incubator has a breakpoint protection function and a delay function of about one and a half minutes. After the compressor stops, it will start up again for about one and a half minutes. In order to ensure the effective heat dissipation of the condenser, the distance between the condenser and the wall is greater than 100mm. There should be a 50mm gap on the side of the box and at least 300mm on the top of the box.
7. The biochemical incubator should avoid collision and shaking when handling, repairing and maintaining; the large inclination of Zui is less than 45 degrees. Stop using, turn off the main power button, and the power switch at the rear of the device. At the same time, avoid frequent opening of the door to keep the temperature stable while preventing dust and dirt from entering.
9. The inside and outside of the box should be kept clean every day, and should be cleaned after each use. For a long time, the plastic dust cover should not be covered and placed in the drying room. At the same time, the inner wall of the box wall and the surface of the equipment should be wiped frequently to keep it clean and increase the transparency of the glass. Do not use acid, alkali or other corrosive solutions to wipe the outer surface.
10. After the training is finished, turn the power switch to “0â€. If you do not remove the item immediately, please do not open the door.
The above 10 points are summarized and summarized for the safe operation of biochemical incubators.
In addition, we must remind everyone that it is not advisable to use biochemical incubators in abnormal environments such as high voltage, high current, strong magnetic field, etc., so as to avoid interference and damage. When cleaning the biochemical incubator, wipe the inner wall of the tank with gauze soaked in alcohol. Sterilize and disinfect, then wipe off the alcohol with dry gauze. Do not use the device for a long time. Please unplug the power supply, and do the operation of each instrument, fault, abnormal record, and timely maintenance.
Shangyu Xingxing Instrument Equipment Co., Ltd. is located in Daoxu Town, Shangyu District, Shaoxing City, Zhejiang Province. It is an enterprise integrating production, product research and development, processing and trade. The company's main products: drying box series, incubator series, laboratory muffle furnace series, distilled water series, as well as clean workbench, air shower, fume hood, biological safety cabinet and other complete purification equipment.
The company has a strong technical research and development team, a strong after-sales guarantee service system, is the linger of the Chinese laboratory complete sets of equipment manufacturers, welcome customers to buy.
1. The biochemical incubator should be installed as close as possible to the place where the air is quiet and the temperature changes little. Use a three-prong plug and the socket should be properly grounded.
2. Before opening the biochemical incubator, you should be familiar with and understand the instructions of each component instrument and instrument, and master the correct method of use.
3. It is strictly forbidden to contain volatile chemical solvents, explosive gases and flammable gases are placed in the box; flammable sprays should not be used near the incubator to avoid spark ignition.
4. Always pay attention to the gas path.
5. The biochemical incubator has a breakpoint protection function and a delay function of about one and a half minutes. After the compressor stops, it will start up again for about one and a half minutes. In order to ensure the effective heat dissipation of the condenser, the distance between the condenser and the wall is greater than 100mm. There should be a 50mm gap on the side of the box and at least 300mm on the top of the box.
7. The biochemical incubator should avoid collision and shaking when handling, repairing and maintaining; the large inclination of Zui is less than 45 degrees. Stop using, turn off the main power button, and the power switch at the rear of the device. At the same time, avoid frequent opening of the door to keep the temperature stable while preventing dust and dirt from entering.
9. The inside and outside of the box should be kept clean every day, and should be cleaned after each use. For a long time, the plastic dust cover should not be covered and placed in the drying room. At the same time, the inner wall of the box wall and the surface of the equipment should be wiped frequently to keep it clean and increase the transparency of the glass. Do not use acid, alkali or other corrosive solutions to wipe the outer surface.
10. After the training is finished, turn the power switch to “0â€. If you do not remove the item immediately, please do not open the door.
The above 10 points are summarized and summarized for the safe operation of biochemical incubators.
In addition, we must remind everyone that it is not advisable to use biochemical incubators in abnormal environments such as high voltage, high current, strong magnetic field, etc., so as to avoid interference and damage. When cleaning the biochemical incubator, wipe the inner wall of the tank with gauze soaked in alcohol. Sterilize and disinfect, then wipe off the alcohol with dry gauze. Do not use the device for a long time. Please unplug the power supply, and do the operation of each instrument, fault, abnormal record, and timely maintenance.
Shangyu Xingxing Instrument Equipment Co., Ltd. is located in Daoxu Town, Shangyu District, Shaoxing City, Zhejiang Province. It is an enterprise integrating production, product research and development, processing and trade. The company's main products: drying box series, incubator series, laboratory muffle furnace series, distilled water series, as well as clean workbench, air shower, fume hood, biological safety cabinet and other complete purification equipment.
The company has a strong technical research and development team, a strong after-sales guarantee service system, is the linger of the Chinese laboratory complete sets of equipment manufacturers, welcome customers to buy.
coffee powder
Selected raw materials, deep roasting and frying, give the coffee a balanced taste
Mellow milk fragrance, long finish, showing delicate baking aroma
Coffee Powder,Espresso Powder,Coffee Powder Grinding,Pure Soluble Coffee Powder
KARAK , https://www.jskarak.com